Maxijet MJ-500 Water Pump

///Maxijet MJ-500 Water Pump

Maxijet MJ-500 Water Pump

£22.95

Maxijet MJ-500 Water Pump – 480l/h 93cm Lift

Nutrient delivery systems are only ever as effective as the pump that’s used to power them. For many years now, Maxijet pumps have been the first port of call, and there are many reasons why. In a nutshell, Maxijet pumps move large quantities of liquid quietly and efficiently, and their reliability is unquestioned. If you’re looking for an effective submersible pump, then there’s really no better all-rounder than a Maxijet. The MJ-500 moves 480 liters of water per hour through a 12.5mm outlet.

Description

Maxijet MJ-500 Water Pump – 480l/h 93cm Lift

Nutrient delivery systems are only ever as effective as the pump that’s used to power them. For many years now, Maxijet pumps have been the first port of call, and there are many reasons why. In a nutshell, Maxijet pumps move large quantities of liquid quietly and efficiently, and their reliability is unquestioned. If you’re looking for an effective submersible pump, then there’s really no better all-rounder than a Maxijet. The MJ-500 moves 480 litres of water per hour through a 12.5mm outlet.

  • Maxijet – tried and tested
  • Corrosion-resistant plastic casing
  • Fully submersible
  • 480 litre / hour flow rate
  • Mountable suction cups to eliminate vibration
  • Reliable – engineered for continuous use
  • Very low maintenance
  • Plastic pre-filter to prevent blockages
  • 2m mains cable equipped with 13amp plug
  • Runs extremely quiet
  • 12.5mm outlet size

The Maxijet MJ-500 Water Pump – 480l/h 93cm Lift Contains:

1 x Maxijet MJ-500 water pump, 1 x plastic pre-filter, 1 x suction cup mounting frame, 3 x suction cups

How the Maxijet MJ-500 Water Pump – 480l/h 93cm Lift Works:

The Maxijet MJ-500 is a fully submersible water pump that moves 480 litres of water per hour through a 12.5mm diameter outlet point. The plastic pre-filter on this unit prevents impurities from passing through the pump and on into pipe networks, lowering the chances of blockages and improving levels of efficiency and reliability. Growers depending on pumps to move nutrient solutions to-and-from root-zones know only too well that blockages and equipment failures can lead to catastrophic effects. If root-systems dry out, there’s only a small timeframe to correct issues before plants start to suffer irreversible damage. Using a high-quality pump with the pedigree of the MJ-500 helps to ensure that the chances of this are greatly reduced. The Maxijet is powerful enough to propel water upwards through a riser pipe of a maximum of 93cm tall. It’s also fitted with an outlet point that can be twisted to sit in any direction, rotating a full 360 degrees.

Using the Maxijet MJ-500 Water Pump – 480l/h 93cm Lift:

Always read the supplied instruction sheet carefully and follow all safety procedures to the letter.The MJ-500 is ideal for use in systems that require the movement of nutrients to-and-from root-zones, such as flood and drain, NFT, run to waste-systems, dripper systems, etc. Set-up is easy: the unit comes with a 12.5mm outlet point that connects directly onto standard, commonly used 13mm pipe (as utilized by IWS and other systems). Use a mini hose clip to tighten the pipe around the outlet point. Once connected, keep the plug on the end of the mains cable well away from any water and submerge the pump in the liquid that you wish to move, securing the unit in place by applying pressure to the mounted suction cups. The exact setup depends on the application / system, but the basic principle is the same: the Maxijet will propel the liquid that it is submerged in through the pipe attached to its outlet.

Weight: 0.43kg
Power: 6 watts
Frequency: 50/60Hz
Flow: 480 L/H
Lift: 93cm / 37”
Dimensions: 50mm x 79mm x 68mm